Connect with us

Space & Physics

A listening device to hear moonquakes

A dense seismic network on the moon can help answer longstanding questions on moonquakes.

Published

on

Credit: Denny Muller / Unsplash

Seismologists from the Woods Hole Oceanographic Institute, US did a theoretical study on the feasibility of detecting moonquakes using fiber seismic network on the Moon. The paper was published in the Seismological Research Letters.

The study can assist with resolving outstanding questions on moonquake research. The Apollo missions saw seismometers detect some thousand seismic events lasting some seven years spanning the 1970s. However, a startling discovery back then was that similar events were never detected from the far side.

Unlike earth where seismic events occur due to fault movements, seismic events on the moon occur due to mostly to the tidal effect when earth gravitationally tugs at the moon. Then there can be thermal moonquakes caused when the icy crust expands due to heat from sunlight, after a long spell of extreme cold. The Apollo’s seismometers detected meteorite impacts triggering seismic waves, in addition to the brittle rock up to some 70 km deep.

NASA’s Passive Seismic Experiment Package (PSEP) planted on the lunar surface during Apollo 11. Credit: DVIDS

A novel seismometer array

The scientists proposed setting up a network of optical fiber cables – dubbed the Distributed Acoustic Sensing (DAS), to operate as an advanced seismometer. DAS detects seismic waves when the light pulse deviates from its trajectory in the fiber.

“It’s a very dense seismic array,” said first author Wenbo Wu, and a seismologist at California Institute of Technology (Caltech) and the Woods Institute.  “One cable can get you thousands of individual sensors. Utilizing advanced signal processing techniques, seismologists suggest it’s possible to decipher signals that are much weaker than stronger seismic signal waves that are otherwise captured with even simple seismometers.

However, the scientists suggested there’s need to demonstrate practical feasibility before it were to be deployed on the moon on some future mission. The researchers suggest it would be possible to combine the possible seismograph project with an astronomy project like setting up a radio telescope, on the far side of the Moon. For the latter project too will require fiber optic cables to connect to an antenna.

“If we can combine these projects together to save the cost, that would really increase the chance to make it happen and have maximum scientific impact,” said Wu.

Space & Physics

MIT unveils an ultra-efficient 5G receiver that may supercharge future smart devices

A key innovation lies in the chip’s clever use of a phenomenon called the Miller effect, which allows small capacitors to perform like larger ones

Published

on

Image credit: Mohamed Hassan from Pixabay

A team of MIT researchers has developed a groundbreaking wireless receiver that could transform the future of Internet of Things (IoT) devices by dramatically improving energy efficiency and resilience to signal interference.

Designed for use in compact, battery-powered smart gadgets—like health monitors, environmental sensors, and industrial trackers—the new chip consumes less than a milliwatt of power and is roughly 30 times more resistant to certain types of interference than conventional receivers.

“This receiver could help expand the capabilities of IoT gadgets,” said Soroush Araei, an electrical engineering graduate student at MIT and lead author of the study, in a media statement. “Devices could become smaller, last longer on a battery, and work more reliably in crowded wireless environments like factory floors or smart cities.”

The chip, recently unveiled at the IEEE Radio Frequency Integrated Circuits Symposium, stands out for its novel use of passive filtering and ultra-small capacitors controlled by tiny switches. These switches require far less power than those typically found in existing IoT receivers.

A key innovation lies in the chip’s clever use of a phenomenon called the Miller effect, which allows small capacitors to perform like larger ones. This means the receiver achieves necessary filtering without relying on bulky components, keeping the circuit size under 0.05 square millimeters.

Credit: Courtesy of the researchers/MIT News

Traditional IoT receivers rely on fixed-frequency filters to block interference, but next-generation 5G-compatible devices need to operate across wider frequency ranges. The MIT design meets this demand using an innovative on-chip switch-capacitor network that blocks unwanted harmonic interference early in the signal chain—before it gets amplified and digitized.

Another critical breakthrough is a technique called bootstrap clocking, which ensures the miniature switches operate correctly even at a low power supply of just 0.6 volts. This helps maintain reliability without adding complex circuitry or draining battery life.

The chip’s minimalist design—using fewer and smaller components—also reduces signal leakage and manufacturing costs, making it well-suited for mass production.

Looking ahead, the MIT team is exploring ways to run the receiver without any dedicated power source—possibly by harvesting ambient energy from nearby Wi-Fi or Bluetooth signals.

The research was conducted by Araei alongside Mohammad Barzgari, Haibo Yang, and senior author Professor Negar Reiskarimian of MIT’s Microsystems Technology Laboratories.

Continue Reading

Society

Ahmedabad Plane Crash: The Science Behind Aircraft Take-Off -Understanding the Physics of Flight

Take-off is one of the most critical phases of flight, relying on the precise orchestration of aerodynamics, propulsion, and control systems. Here’s how it works:

Published

on

On June 12, 2025, a tragic aviation accident struck Ahmedabad, India when a regional passenger aircraft, Air India flight A1-171, crashed during take-off at Sardar Vallabhbhai Patel International Airport. According to preliminary reports, the incident resulted in over 200 confirmed casualties, including both passengers and crew members, and several others are critically injured. The aviation community and scientific world now turn their eyes not just toward the cause but also toward understanding the complex science behind what should have been a routine take-off.

How Do Aircraft Take Off?

Take-off is one of the most critical phases of flight, relying on the precise orchestration of aerodynamics, propulsion, and control systems. Here’s how it works:

1. Lift and Thrust

To leave the ground, an aircraft must generate lift, a force that counters gravity. This is achieved through the unique shape of the wing, called an airfoil, which creates a pressure difference — higher pressure under the wing and lower pressure above — according to Bernoulli’s Principle and Newton’s Third Law.

Simultaneously, engines provide thrust, propelling the aircraft forward. Most commercial jets use turbofan engines, which accelerate air through turbines to generate power.

2. Critical Speeds

Before takeoff, pilots calculate critical speeds:

  • V1 (Decision Speed): The last moment a takeoff can be safely aborted.
  • Vr (Rotation Speed): The speed at which the pilot begins to lift the nose.
  • V2 (Takeoff Safety Speed): The speed needed to climb safely even if one engine fails.

If anything disrupts this process — like bird strikes, engine failure, or runway obstructions — the results can be catastrophic.

Environmental and Mechanical Challenges

Factors like wind shear, runway surface condition, mechanical integrity, or pilot error can interfere with safe take-off. Investigators will be analyzing these very aspects in the Ahmedabad case.

The Bigger Picture

Take-off accounts for a small fraction of total flight time but is disproportionately associated with accidents — approximately 14% of all aviation accidents occur during take-off or initial climb.

Continue Reading

Space & Physics

MIT claims breakthrough in simulating physics of squishy, elastic materials

In a series of experiments, the new solver demonstrated its ability to simulate a diverse array of elastic behaviors, ranging from bouncing geometric shapes to soft, squishy characters

Published

on

Image credit: Courtesy of researchers

Researchers at MIT claim to have unveiled a novel physics-based simulation method that significantly improves stability and accuracy when modeling elastic materials — a key development for industries spanning animation, engineering, and digital fabrication.

In a series of experiments, the new solver demonstrated its ability to simulate a diverse array of elastic behaviors, ranging from bouncing geometric shapes to soft, squishy characters. Crucially, it maintained important physical properties and remained stable over long periods of time — an area where many existing methods falter.

Other simulation techniques frequently struggled in tests: some became unstable and caused erratic behavior, while others introduced excessive damping that distorted the motion. In contrast, the new method preserved elasticity without compromising reliability.

“Because our method demonstrates more stability, it can give animators more reliability and confidence when simulating anything elastic, whether it’s something from the real world or even something completely imaginary,” Leticia Mattos Da Silva, a graduate student at MIT’s Department of Electrical Engineering and Computer Science, said in a media statement.

Their study, though not yet peer-reviewed or published, will be presented at the August proceedings of the SIGGRAPH conference in Vancouver, Canada.

While the solver does not prioritize speed as aggressively as some tools, it avoids the accuracy and robustness trade-offs often associated with faster methods. It also sidesteps the complexity of nonlinear solvers, which are commonly used in physics-based approaches but are often sensitive and prone to failure.

Looking ahead, the research team aims to reduce computational costs and broaden the solver’s applications. One promising direction is in engineering and fabrication, where accurate elastic simulations could enhance the design of real-world products such as garments, medical devices, and toys.

“We were able to revive an old class of integrators in our work. My guess is there are other examples where researchers can revisit a problem to find a hidden convexity structure that could offer a lot of advantages,” Mattos Da Silva added.

The study opens new possibilities not only for digital content creation but also for practical design fields that rely on predictive simulations of flexible materials.

Continue Reading

Trending